BS 4102-1998 Steel wire for general fencing purposes
|
ID： |
21C13E10249B4F198DF2016E4B880CCE |
|
文件大小(MB)： |
0.12 |
|
页数： |
8 |
|
文件格式： |
|
|
日期： |
2008-10-7 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BRITISH STANDARD BS 4102:1998,ICS 77.140.65,NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW,Specification for,Steel wire for general,fencing purposes,This British Standard, having,been prepared under the,direction of the Engineering,Sector Board, was published,under the authority of the,Standards Board and comes into,effect on,15 June 1998,ó BSI 1998,The following BSI references,relate to the work on this,standard:,Committee reference ISE/26,ISBN 0 580 29537 0,BS 4102:1998,Amendments issued since publication,Amd. No. Date Text affected,Committees responsible for this,British Standard,The preparation of this British Standard was entrusted to Technical Committee,ISE/26, Steel wire, upon which the following bodies were represented:,Bicycle Association of GB,British Cable Makers Confederation,British Rubber Manufacturers Association Ltd.,British Stainless Steel Association,Electricity Association,Federation of Wire Rope Manufacturers of Great Britain,Forestry Commission,Health and Safety Executive,Institute of Spring Technology,National Centre of Tribology,Society of Chain Link Fencing Manufacturers,Society of Motor Manufacturers and Traders Limited,Stainless Steel Wire Industry Association,UK Steel Association,Welding Manufacturers Association (BEAMA Ltd.),Woven Wire Association,BS 4102:1998,ó BSI 1998 i,Contents,Page,Committees responsible Inside front cover,Foreword ii,1 Scope 1,2 Normative references 1,3 Materials 1,4 Wire diameter and tolerances 1,5 Coatings 1,6 Tensile strength 1,7 Inspection and testing 2,8 Marking 2,Table 1 D Nominal diameters of wires for general fencing purposes 1,Table 2 D Minimum tensile strength for drawn carbon steel line wire 2,ii ó BSI 1998,BS 4102:1998,Foreword,This British Standard has been prepared by Technical Committee ISE/26. It supersedes,BS 4102:1990 which is withdrawn. This new edition of BS 4102 has been editorially,amended to remove technical requirements which have been superseded by European,Standards. It does not constitute a full revision of the standard.,This new edition of BS 4102 does not specify requirements for:,D wire for chain linking fence;,D barbed wire;,D wire and woven wire mesh for hinged joint fencing; and,D welded steel wire mesh.,Requirements for these wires have been included in BS EN 10223-1, -4, -5 and -6,published simultaneously with this British Standard.,A British Standard does not purport to include all necessary provisions of a contract.,Users of British Standards are responsible for their correct application.,Compliance with a British Standard does not of itself confer immunity,from legal obligations.,Summary of pages,This document comprises a front cover, an inside front cover, pages i and ii, pages 1,and 2, an inside back cover and a back cover.,ó BSI 1998 1,BS 4102:1998,Table 1 – Nominal diameters of wires for general fencing purposes,Nominal wire diameter Approximate length,per 100 kg,Nominal wire diameter Approximate length,per 100 kg,mm m mm m,1.60 6359 3.00 1809,1.90 4510 3.15 1641,2.00 4070 3.55 1292,2.24 3245 4.00 1018,2.50 26.5 4.50 804,2.65 2318 5.00 651,1 Scope,This British Standard specifies requirements for zinc,coated steel wire, used in the construction of fences,including those conforming to BS 1722 for the,following applications:,a) wire for cleft chestnut pale fencing;,b) general purpose line wire;,c) general purpose stirrup wire;,d) general purpose tying wire;,e) organic coated wire for strained wire dropper,fencing.,2 Normative references,The following normative documents contain,provisions which, through reference in this text,constitute provisions of this British Standard. For,dated references, subsequent amendments to, or,revisions of, any of these publications do not apply.,For undated references, the latest edition of the,publication referred to applies.,BS EN 10218-1, Steel wire and wire products D,General D Part 1: Test methods.,BS EN 10218-2, Steel wire and wire products D,General D Part 2: Wire dimensions and tolerances.,BS EN 10244-1, Non-ferrous metallic coating for steel,wire D Part 1: General principles.,BS EN 10244-2, Non-ferrous metallic coating for steel,wire D Part 2: Zinc and zinc alloy coatings.,BS 1722-3, Fences D Part 3: Specification for,strained wire fences.,3 Materials,3.1 The wire shall be as uniform as possible and,free from internal and surface defects that could,adversely affect its performance. Wire in coil shall be,adead casto to lie in uniform circles with no,significant helical lift.,NOTE Where wire has been zinc coated by the hot dip method,thick coatings may not be entirely free from surface irregularities,and, provided these are ……
……